A climate chamber does exactly what lighting tolerates worst: cycling between extreme cold and extreme heat, with condensation at every transition.
Standard luminaires fill with moisture, lose light output or fail in the middle of a test run, and an interrupted endurance test is a lost endurance test. Our luminaires are specified from -45 °C to +120 °C ambient temperature and tested on precisely this cyclic profile.
Specified range, AC version
Most compact luminaire, for small chambers
Light level controllable from the cool zone
Not the peak but the cycling is the killer: expansion and contraction with every cycle. Materials, seals and cabling are selected for exactly this.
IP67 sealing and glass, so the transition from freezing to heat draws no moisture inside.
Why a high IP rating says nothing about temperature resistance is explained under IP and IK ratings.
Test room volume is precious; the Goby HT is there for small chambers from 2,600 lumens.
Light level as a test variable, controllable from the cool zone.
| Requirement | Why the requirement exists | How the luminaire meets it |
|---|---|---|
| Cyclic loading | Expansion and contraction with every switch between cold and heat | Specified as a system from -45 °C to +120 °C |
| Condensation resistance | Moisture at every transition from freezing to warm | IP67 seal and a glass front |
| Compact size | Test space is valuable volume | Goby HT, 2,600 lm at 13 W |
| Dimmable | The light level is a test variable | Controllable from the cool zone |
Compact, for small chambers and close to the object. AC up to +120 °C, DC 24V up to +110 °C.
For larger chambers and walk-in rooms. Also available fully in 316L stainless steel.
Control and driver outside the chamber, so no heat source or failure source in the test room itself.
The temperature range: AC versions from -45 °C to +120 °C, 24 V DC versions up to +110 °C. The Goby HT suits small chambers and positions close to the test object, the Snapper HT larger chambers and walk-in rooms.
The same luminaires are specified down to -45 °C. That also makes them suitable as LED lighting for a freezer room or cold room, where the problem works the other way round: not the heat, but the cold and the condensation at the transition. Every time the door opens, warm, humid air condenses on cold surfaces; an IP67 seal with a glass front keeps that moisture out.
Here too, the driver sits outside the room. That keeps the electronics out of the cold and its heat out of the room, and driver maintenance happens without entering the room.
In every case the same logic applies: the test is the product, and the lighting must never be the variable that disturbs the run.
Why the same luminaires are also specified down to -45 °C is explained in the article on lighting for high and low temperature environments.
Is your question not listed? Call 033 785 9809, you will speak with an engineer.
Luminaires designed as a system for that range: glass instead of plastic, seals and cabling that withstand the cycling, and the driver outside the chamber. Our AC versions are specified from -45 °C to +120 °C, DC versions (24V) up to +110 °C.
The switch does the work, more than the peak. Every cycle makes materials expand and contract and, during the transition from freezing to heat, draws in moisture. In addition, the driver ages at an accelerated rate at high temperature and is the first to fail.
With an IP67 seal, a glass front and materials that keep their shape through every cycle. A luminaire that has once let moisture in never gets rid of it under cyclic testing.
Yes. The light level is controllable from the cool zone, outside the chamber, and can thus be included in the protocol as a test variable.
The Goby HT delivers 2,600 lumens at 13 W and is built for small chambers where every bit of volume counts.
The driver sits outside the chamber; the luminaire itself adds minimal power, and that amount is known and constant, so it can be included in the chamber balance.
IP67 with a glass front, because condensation tries to draw moisture inside with every cycle. A high IP rating says nothing about temperature resistance. So set both requirements separately: IP67 for the moisture, and a specified range of -45 °C to +120 °C for the temperature.
Lighting for climate chambers belongs to the sector heavy industry.
Climate chambers are the most demanding cyclic application of our high temperature LED lights, with the same published L90B05 lifespan curve.