Manta LED canopy light

One canopy shape for every canopy: 22,400 lumens at 224 lm/W, dimmable with 0-10V, PWM, DALI-2, or NFC.

Available as a recessed or surface-mounted fixture, and as a 21-mm-thick retrofit panel that fits perfectly into an existing CREE 304 mounting location. New is the Manta HT: the same design, built for environments up to +120 °C, for drying tunnels, steam-cleaning car washes, and hot process rooms where no ceiling fixture was previously available.

A response from an engineer within 1 business day. Free lighting analysis and comparison with your current system.

Manta canopy lights in a gas station canopy.

Luminous flux

22,400 lm

100 W, 224 lm/W

Power

10–100 W

Adjustable via NFC, HT 10–75 W

Protection

IP69K

IK08, diffuse tempered glass or borosilicate

Building height

21 mm

built-in, 3.9 kg

Warranty

5 years

limited, including on the HT

Temperature

+120 °C

from −45 °C to +120 °C with the HT

Versions Specifications Optics Retrofit Downloads FAQ

Decision Aid

When do you choose the Manta

This is a light fixture designed to be mounted underneath something: an awning, a ceiling, or a canopy. It doesn't illuminate an outdoor area but rather a living space.

A gas station, a canopy, or a covered outdoor area should be lit from the ceiling
Replace existing canopy lights, specifically the CREE 304
Both surface-mount and flush-mount installations are required within a single project, from the same product line
Efficiency matters: 224 lm/W is the highest efficiency in our product line
The power per position must vary: 10 to 100 W adjustable via NFC
The ambient temperature is warm: the HT version operates up to +120 °C
The position is difficult to reach and every lamp replacement requires an aerial work platform

When another luminaire fits better

As soon as there is nothing above the fixture, or as soon as a distance needs to be bridged, a floodlight or a vlakstraler is the more logical choice.

If it must be illuminated close to a machine or vehicle: then a work light
It is about a larger open work zone: than a floodlight
Light pollution must be actively limited: then a DarkLicht-solution
It is about a facade: then the DarkLicht WP wallpack
A decorative or architectural luminaire is more important than robustness
ATEX or Ex-certification is required; see the question about zoning at petrol stations

Versions

Six versions, the same 380 by 380 millimeters

All versions share the same square dimension; what differs is the installation depth, the weight, and in the case of the HT, the entire thermal design. In the standard versions, the driver is located internally, while in the HT it is external, outside of the hot zone.

Manta Ray Sanctuary

built-in, 380 × 380 × 21 mm

Blends seamlessly into the canopy or suspended ceiling for a seamless final appearance. The logical choice for new construction and renovation where ceiling integration matters. 3.9 kg.

MNAC02

Manta Surface

surface-mounted, 380 × 380 × 70 mm

Mounted directly to the ceiling or substructure, without a recess. For existing ceilings without installation space, steel structures, parking decks, and drive-through zones. 4.9 kg.

MNAC01

Manta Surface Extended

surface-mounted, 380 × 380 × 118 mm

The extended surface-mounted version, and at the same time the retrofit panel: this version fits into an existing CREE 304 cutout, so the canopy ceiling can remain closed. Same light engine, 5.4 kg.

See the retrofit tire

article code MNAC03

Manta HT, built-in

up to +120 °C, external driver

For drying tunnels, car washes with steam cleaning, and hot process rooms. Chemically toughened glass, heat-resistant silicone cable, and an external driver outside the hot zone. Optionally with infrared-reflective print.

Manta HT, surface-mounted

up to +120 °C, external driver

Same HT structure, mounted directly to the ceiling or substructure. For hot zones without installation space, or where the ceiling must not be penetrated.

MNHT01

Product family

The position of the Manta within the building-related line

The Manta hangs under a canopy or ceiling. If it concerns a linear arrangement, a facade, or a site, the answer is elsewhere in the program.

Luminaire	Role in the range	Mounting position
Manta canopy 22,400 lumens	The canopy for under an awning, ceiling, or canopy. Recessed, surface-mounted, and retrofit from a single line, also up to +120 °C.	ceiling and awning
Linear 25,600 lumens	Linear industrial lighting for continuous runs along corridors, machinery, and walkways.	ceiling and wall
DarkLicht WP wallpack 16,000 lumens	Wall-mounted fixture with a full cut-off reflector that directs the light forward, with no upward light.	facade
DarkLicht D 34,200 lumens	Full-cut-off floodlight for outdoor areas and parking lots where light pollution must be actively minimized.	mast and structure

Specifications

Full specification

Choose a trim level and the complete specification list below changes accordingly: the three standard trim levels and the two HT trim levels. Image, key figures, and specifications all update at once, without a second tab.

Item number

MNAC02

The recessed version is installed flush with the ceiling.

22,400 lm

Light

Luminous flux	22,400 lm
With optics	20,600 lm with optics
Efficiency	224 lm/W
Power consumption	100 W
Beam angles	no standard optics, or 30°, 60° or 120°
Bundle and field angle	136° / 168° without optics · 36° / 58° with the 30° optics
Color temperatures	5700K, 5000K, 4000K, 3000K, 2700K and amber 2200K
Tunable white	4000K with 2200K and 1700K, switchable during operation
Bi-color	cool white with amber
CRI (Ra)	> 70, or optionally 80 or 90
Color consistency	3-step MacAdam
ULOR	0 % at 0° tilt

Electric

Voltage range	90 to 305 VAC, 50/60 Hz
Current draw	approx. 0.83 A at 120 V · 0.45 to 0.36 A at 220 to 277 V
DC power supply	Not available for this model
Dimming	0-10 V, PWM, DALI-2 or via NFC
Driver	internal
Driver Type	BLD120, in the housing
Surge protection	6 kV line-to-line, 10 kV line-to-ground (IEC 61000-4-5)
Power factor	> 0.9 at 70 to 100 % load
Cable type	H07BQ-F, 4-core (2 × 1.5 mm² + 2 × 0.5 mm²), 0.3 m
Connection	pre-assembled, bare wires

Construction

Housing	cast aluminum, < 0.08 % copper
Surface treatment	conversion layer with 2-layer titanium e-coating
Bracket	fixed bracket, aluminum, < 0.08 % copper
Front	diffuse chemically strengthened glass or diffuse borosilicate, IK08
Color	Neutral White
Dimensions	380 × 380 × 21 mm
Weight	3.9 kg
Lead time	Standard within a week, custom by arrangement
Packaging	on request

Protection and durability

IP Ratings	IP66, IP67, IP68, and IP69K, each tested individually
Impact Resistance	IK08 (IEC 62262)
Protection Class	Class II
Corrosion class	C5 Industrial and Maritime (ISO 9223)
Vibration class	6 G at resonance (IEC 60068-2-6), shock IEC 60068-2-27
Operating temperature	−45 to +50 °C
LED lifespan	TM-21 L90B05, > 103,500 hours at +50 °C
Driver lifespan	≥ 100,000 hours at Tc 75 °C
MTBF driver	≥ 320,000 hours at Tc 75 °C
Driver Temperature	Temperature: −40 to +90 °C
Warranty	5 years on the complete luminaire
Certification	CE, IEC/EN 60598-1 and -2-5, EN 55015, and EN 61547. EMC tested by TÜV; IEC 60533 for marine applications.

Item number

MNAC01

The surface-mounted version, to be installed without a recess.

22,400 lm

Light

Luminous flux	22,400 lm
With optics	20,600 lm with optics
Efficiency	224 lm/W
Power consumption	100 W
Beam angles	no standard optics, or 30°, 60° or 120°
Bundle and field angle	136° / 168° without optics · 36° / 58° with the 30° optics
Color temperatures	5700K, 5000K, 4000K, 3000K, 2700K and amber 2200K
Tunable white	4000K with 2200K and 1700K, switchable during operation
Bi-color	cool white with amber
CRI (Ra)	> 70, or optionally 80 or 90
Color consistency	3-step MacAdam
ULOR	0 % at 0° tilt

Electric

Voltage range	90 to 305 VAC, 50/60 Hz
Current draw	approx. 0.83 A at 120 V · 0.45 to 0.36 A at 220 to 277 V
DC power supply	Not available for this model
Dimming	0-10 V, PWM, DALI-2 or via NFC
Driver	internal
Driver Type	BLD120, in the housing
Surge protection	6 kV line-to-line, 10 kV line-to-ground (IEC 61000-4-5)
Power factor	> 0.9 at 70 to 100 % load
Cable type	H07BQ-F, 4-core (2 × 1.5 mm² + 2 × 0.5 mm²), 0.3 m
Connection	pre-assembled, bare wires

Construction

Housing	cast aluminum, < 0.08 % copper
Surface treatment	conversion layer with 2-layer titanium e-coating
Bracket	fixed bracket, aluminum, < 0.08 % copper
Front	diffuse chemically strengthened glass or diffuse borosilicate, IK08
Color	Neutral White
Dimensions	380 × 380 × 70 mm
Weight	4.9 kg
Packaging	on request

Protection and durability

IP Ratings	IP66, IP67, IP68, and IP69K, each tested individually
Impact Resistance	IK08 (IEC 62262)
Protection Class	Class II
Corrosion class	C5 Industrial and Maritime (ISO 9223)
Vibration class	6 G at resonance (IEC 60068-2-6), shock IEC 60068-2-27
Operating temperature	−45 to +50 °C
LED lifespan	TM-21 L90B05, > 103,500 hours at +50 °C
Driver lifespan	≥ 100,000 hours at Tc 75 °C
MTBF driver	≥ 320,000 hours at Tc 75 °C
Driver Temperature	Temperature: −40 to +90 °C
Warranty	5 years on the complete luminaire
Certification	CE, IEC/EN 60598-1 and -2-5, EN 55015, and EN 61547. EMC tested by TÜV; IEC 60533 for marine applications.

Item number

MNAC03

The surface-mounted version with an extended housing.

22,400 lm

Light

Luminous flux	22,400 lm
With optics	20,600 lm with optics
Efficiency	224 lm/W
Power consumption	100 W
Beam angles	no standard optics, or 30°, 60° or 120°
Bundle and field angle	136° / 168° without optics · 36° / 58° with the 30° optics
Color temperatures	5700K, 5000K, 4000K, 3000K, 2700K and amber 2200K
Tunable white	4000K with 2200K and 1700K, switchable during operation
Bi-color	cool white with amber
CRI (Ra)	> 70, or optionally 80 or 90
Color consistency	3-step MacAdam
ULOR	0 % at 0° tilt

Electric

Voltage range	90 to 305 VAC, 50/60 Hz
Current draw	approx. 0.83 A at 120 V · 0.45 to 0.36 A at 220 to 277 V
DC power supply	Not available for this model
Dimming	0-10 V, PWM, DALI-2 or via NFC
Driver	internal
Driver Type	BLD120, in the housing
Surge protection	6 kV line-to-line, 10 kV line-to-ground (IEC 61000-4-5)
Power factor	> 0.9 at 70 to 100 % load
Cable type	H07BQ-F, 4-core (2 × 1.5 mm² + 2 × 0.5 mm²), 0.3 m
Connection	pre-assembled, bare wires

Construction

Housing	cast aluminum, < 0.08 % copper
Surface treatment	conversion layer with 2-layer titanium e-coating
Bracket	fixed bracket, aluminum, < 0.08 % copper
Front	diffuse chemically strengthened glass or diffuse borosilicate, IK08
Color	Neutral White
Dimensions	380 × 380 × 118 mm
Weight	5.4 kg
Packaging	on request

Protection and durability

IP Ratings	IP66, IP67, IP68, and IP69K, each tested individually
Impact Resistance	IK08 (IEC 62262)
Protection Class	Class II
Corrosion class	C5 Industrial and Maritime (ISO 9223)
Vibration class	6 G at resonance (IEC 60068-2-6), shock IEC 60068-2-27
Operating temperature	−45 to +50 °C
LED lifespan	TM-21 L90B05, > 103,500 hours at +50 °C
Driver lifespan	≥ 100,000 hours at Tc 75 °C
MTBF driver	≥ 320,000 hours at Tc 75 °C
Driver Temperature	Temperature: −40 to +90 °C
Warranty	5 years on the complete luminaire
Certification	CE, IEC/EN 60598-1 and -2-5, EN 55015, and EN 61547. EMC tested by TÜV; IEC 60533 for marine applications.

Item number

MNHT02

The high-temperature recessed version, up to +120 °C with an external driver.

14,400 lm

Light

Luminous flux	14,400 lm
With optics	no lenses possible
Efficiency	192 lm/W
Power consumption	75 W
Beam angles	120° very wide, no optics possible
Bundle and field angle	136° / 168°
Color temperatures	6500K, 4000K, and 2700K
Tunable white	not available on the HT versions
Bi-color	not available on the HT versions
CRI (Ra)	> 70, or optionally 80 or 90
Color consistency	3-step MacAdam
ULOR	0 % at 0° tilt

Electric

Voltage range	90 to 305 VAC, 50/60 Hz
Current draw	approx. 0.63 A at 120 V · 0.34 to 0.27 A at 220 to 277 V
DC power supply	127 to 420 VDC, warranty up to +110 °C
Dimming	0-10 V, PWM, DALI-2 or via NFC
Driver	external, outside the hot zone
Driver Type	BLD120, 90 to 305 VAC or 127 to 420 VDC
Driverbox	DRB-1, 276 × 194 × 86.5 mm, 4.2 kg, IP66 and IP67
Surge protection	6 kV line-to-line, 10 kV line-to-ground (IEC 61000-4-5)
Power factor	> 0.9 at 70 to 100 % load
Cable type	SiHF-OB silicone cable, 4 conductors (2 × 2.5 mm² + 2 × 0.5 mm²), 5.0 m
Connection	pre-assembled, bare wires
Self-protection	Internal temperature feedback via two control pins; dims and shuts off in case of overheating

Construction

Housing	cast aluminum, < 0.08 % copper
Surface treatment	conversion layer with 2-layer titanium e-coating
Bracket	fixed bracket, aluminum, < 0.08 % copper
Front	diffuse chemically strengthened glass or diffuse borosilicate, IK08
Color	Titanium light gray
Dimensions	380 × 380 × 21 mm
Weight	3.9 kg
Packaging	on request

Protection and durability

IP Ratings	IP66, IP67, IP68, and IP69K, resistant to steam and high-pressure cleaning
Impact Resistance	IK08 (IEC 62262)
Protection Class	Class II
Corrosion class	C5 Industrial and Maritime (ISO 9223)
Vibration class	6 G at resonance (IEC 60068-2-6), shock IEC 60068-2-27
Operating temperature	-45 to +120 °C, peaks up to +130 °C
Driverbox Environment	up to +50 °C
LED lifespan	TM-21 L90B05: 360,000 hours at +50 °C · 103,000 at +85 °C · 71,700 at +105 °C · 51,400 at +120 °C
Driver lifespan	≥ 100,000 hours at Tc 75 °C
MTBF driver	≥ 320,000 hours at Tc 75 °C
Driver Temperature	Temperature: −40 to +90 °C
Warranty	5-year warranty on the entire fixture up to +120 °C on AC, up to +110 °C on DC
Certification	CE, IEC/EN 60598-1 and -2-5, EN 55015, and EN 61547. EMC tested by TÜV; IEC 60533 for marine applications.

Item number

MNHT01

The surface-mount high-temperature version, up to +120 °C with an external driver.

14,400 lm

Light

Luminous flux	14,400 lm
With optics	no lenses possible
Efficiency	192 lm/W
Power consumption	75 W
Beam angles	120° very wide, no optics possible
Bundle and field angle	136° / 168°
Color temperatures	6500K, 4000K, and 2700K
Tunable white	not available on the HT versions
Bi-color	not available on the HT versions
CRI (Ra)	> 70, or optionally 80 or 90
Color consistency	3-step MacAdam
ULOR	0 % at 0° tilt

Electric

Voltage range	90 to 305 VAC, 50/60 Hz
Current draw	approx. 0.63 A at 120 V · 0.34 to 0.27 A at 220 to 277 V
DC power supply	127 to 420 VDC, warranty up to +110 °C
Dimming	0-10 V, PWM, DALI-2 or via NFC
Driver	external, outside the hot zone
Driver Type	BLD120, 90 to 305 VAC or 127 to 420 VDC
Driverbox	DRB-1, 276 × 194 × 86.5 mm, 4.2 kg, IP66 and IP67
Surge protection	6 kV line-to-line, 10 kV line-to-ground (IEC 61000-4-5)
Power factor	> 0.9 at 70 to 100 % load
Cable type	SiHF-OB silicone cable, 4 conductors (2 × 2.5 mm² + 2 × 0.5 mm²), 5.0 m
Connection	pre-assembled, bare wires
Self-protection	Internal temperature feedback via two control pins; dims and shuts off in case of overheating

Construction

Housing	cast aluminum, < 0.08 % copper
Surface treatment	conversion layer with 2-layer titanium e-coating
Bracket	fixed bracket, aluminum, < 0.08 % copper
Front	diffuse chemically strengthened glass or diffuse borosilicate, IK08
Color	Titanium light gray
Dimensions	380 × 380 × 70 mm
Weight	4.9 kg
Packaging	on request

Protection and durability

IP Ratings	IP66, IP67, IP68, and IP69K, resistant to steam and high-pressure cleaning
Impact Resistance	IK08 (IEC 62262)
Protection Class	Class II
Corrosion class	C5 Industrial and Maritime (ISO 9223)
Vibration class	6 G at resonance (IEC 60068-2-6), shock IEC 60068-2-27
Operating temperature	-45 to +120 °C, peaks up to +130 °C
Driverbox Environment	up to +50 °C
LED lifespan	TM-21 L90B05: 360,000 hours at +50 °C · 103,000 at +85 °C · 71,700 at +105 °C · 51,400 at +120 °C
Driver lifespan	≥ 100,000 hours at Tc 75 °C
MTBF driver	≥ 320,000 hours at Tc 75 °C
Driver Temperature	Temperature: −40 to +90 °C
Warranty	5-year warranty on the entire fixture up to +120 °C on AC, up to +110 °C on DC
Certification	CE, IEC/EN 60598-1 and -2-5, EN 55015, and EN 61547. EMC tested by TÜV; IEC 60533 for marine applications.

Instant download, no form required. All the values listed above are also included in the datasheet.

For the installer

Connecting and Setting Up

The luminaire is supplied with a pre-assembled connection cable with free leads: 0.3-meter H07BQ-F with four leads for the standard versions, 5-meter heat-resistant SiHF-OB silicone cable for the HT.

Voltage range

90–305 VAC

also 120 V, internal driver

Power consumption: 100 W

0.45–0.36 A

at 220 to 277 V · 0.83 A at 120 V

Power Consumption: 75 W HT

0.34–0.27 A

at 220 to 277 V · 0.63 A at 120 V

Dimming

0–10 V · DALI-2

PWM or via NFC, per position

Dimming by position

The light level is controlled via 0-10 V, PWM, or DALI-2, and,via NFC,also using a phone or programming box, without opening the fixture or disconnecting the power. For a canopy with multiple zones, you can set a different light level for each position and adjust them later if the layout changes: a position above the pumps can be set higher than one above the passageway.

With the standard versions, the driver is internal and the fixture operates directly from 90 to 305 volts. With the HT, the driver is external and remains outside the hot zone: drivers are more sensitive to heat than the LED module itself, and this makes maintenance possible without entering the hot room. We will calculate your canopy free of charge: see lighting advice and lighting calculation.

Other electrical

Driver intern at Recess, Surface and Surface Extended
External driver at the HT, outside the hot zone and separately replaceable
Driverbox DRB-1 at the HT, 276 × 194 × 86.5 mm, IP66 and IP67, maximum ambient temperature +50 °C
Cable H07BQ-F 0.3 m with four cores, with the HT SiHF-OB silicone 5.0 m heat-resistant
Connection pre-assembled, bare wires
Dimming: 0–10 V, PWM, DALI-2, or via NFC
CE and IEC/EN 60598-1 and -2-5 certification; EMC tested by TÜV
Surge protection 6 kV line-line, 10 kV line-earth according to IEC 61000-4-5
Work factor > 0.9 at 70 to 100 percent load
DC power supply only for the HT, 127 to 420 VDC; the standard models are AC

Optics

Beam angles and light distribution

Under a canopy, the beam angle determines whether the edge of the canopy still receives light. The standard models are available with 30°, 60°, or 120° angles; the HT model has a fixed 120° angle. If you’re unsure between two angles, we’ll help you make the right choice with a free lighting calculation.

30° beam

Directed beam for a high canopy or a narrow passageway. All three recessed depths share the same optical platform and photometry.

60° beam

The center distribution for most awnings: even, with no bright spot in view.

120° extra-wide

Wide distribution for low canopies and covered walkways, and the fixed distribution of the HT version.

Optics	Luminous flux	Version	Application
30°	20,600 lm	standard	Directed beam, 36° beam angle and 58° field angle. High canopies and narrow zones, with optics approx. 206 lm/W.
60°	20,600 lm	standard	Center divider, the standard choice under a gas station canopy.
120°	20,600 lm	standard	Very wide, for low awnings and close positions.
Without optics	22,400 lm	standard	The standard version: 136° beam angle and 168° field angle, the luminous flux of the light engine itself at 224 lm/W.
120°, fixed, HT	14,400 lm	HT	No lenses possible: the housing is too shallow to wear any.

The light engine has a luminous flux of 22,400 lumens; 20,600 lumens is the output with optics; each lens reduces the light output. As a result, the efficiency ranges from 224 lm/W without specific optics to approximately 206 lm/W with optics. We base our calculations on the value corresponding to your chosen optics. With the HT model, lenses are not possible due to the high temperatures.

Retrofit

The existing hole, without demolition work

The CREE 304 is used worldwide and hangs at thousands of service stations. Anyone replacing that installation normally runs into the same problem: the new luminaire does not fit into the existing cutout, which leaves you stuck with demolition work, new cabling, and a second visit.

The Manta Surface Extended is designed for just that: 118 mm deep, 5.4 kg, and it fits into an existing CREE 304 cutout. No new cutout, no new wiring.

No demolition work	The panel fits into the existing cutout, so the ceiling of the canopy remains closed and no repair work is required.
No new cabling	The existing connection will remain in use. That not only saves material, but above all a second visit from the installer.
Minimal downtime per canopy	For a chain with many locations, that counts double: every position that remains closed longer than necessary costs revenue.
Dimmable per position	Dimming via 0-10V, PWM, DALI-2 or NFC, even after the panel is installed. A position above the pumps can be set higher than a position above the drive-through.

Building height

118 mm

from the panel

Weight

5.4 kg

per luminaire

We calculate your awning free of charge and include the comparison with the existing situation. Send a photo of the current position, and we will confirm the fit in advance.

Manta HT

A canopy that can withstand +120 degrees

Until now, ceiling fixtures were rarely installed in drying tunnels or steam-cleaning car washes, simply because none existed that could withstand the conditions. The Manta HT has the same shape and the same 380 by 380 millimeter dimensions, but a different thermal design: chemically tempered glass or borosilicate on the front, a 5-meter heat-resistant SiHF-OB silicone cable, and an external driver that remains outside the hot zone.

In heat, lifespan is not a number but a curve, and we prefer to write that down rather than name a single value. Next to this is the specification per ambient temperature, measured according to TM-21 and reported as L90B05, equal to the rest of the program.

Watch out for the HT

Due to the high temperatures, lenses are not possible: the HT has a single beam angle of 120 degrees, very wide, with a field angle of 168 degrees. If you want a narrower beam in a hot zone, a floodlight from the high-temperature line the correct route.

Ambient Temperature	Service Life L90B05
+50 °C	360,000 hours
+85 °C	103,000 hours
+105 °C	71,700 hours
+120 °C	51,400 hours

Even 51,400 hours is still well over fourteen years at ten burning hours a day. See also High-temperature lighting.

Applications

Wherever people are standing waiting under a roof

A canopy does not illuminate an area but rather a place to stay. People stand there quietly, look up, and subconsciously assess whether it feels safe. This imposes different requirements than outdoor lighting: the light must be even, with no bright source in view, and without a dark edge along the outer edge of the canopy.

Gas Stations

The core application, and the place where the CREE 304 is most frequently installed. High light output, neat ceiling integration, and years of reliable operation above an area where you cannot simply place a cherry picker.

View area lighting

Canopies and awnings

Covered outdoor areas where functional and uniform light is required in a dust- and waterproof design. Outdoor in terms of load capacity, indoor in terms of light distribution: wet and dirty, but out of direct rain.

View infrastructure and site

Service and loading zones

At fast chargers, people linger longer than at a fuel pump, often alone and in the dark. Good ceiling lighting directly determines how safe it feels here, and the power output per position can be adjusted to suit the zone.

View lighting advice and calculation

Warm process rooms

With the HT version also in drying tunnels, drying lines, car washes with steam cleaning, and hot zones in the food and paper industries. Up to +120 °C, with the driver outside the hot zone.

Explore heavy industry and extreme heat

Dimensioning

Dimensions per version

All dimensions in millimeters. All versions share the same 380 by 380 square; only the installation depth and weight differ. DXF and STEP files are available upon request.

Cable length: 0.3 m for standard models, 5.0 m silicone cable for the HT model; longer lengths available upon request. Packaging dimensions available upon request; packaging size and weight are included in the quote, as JEL handles shipping.

Version	Dimensions	Weight
Manta Ray Sanctuary	380 × 380 × 21 mm	3.9 kg
Manta Surface	380 × 380 × 70 mm	4.9 kg
Manta Surface Extended	380 × 380 × 118 mm	5.4 kg
Manta HT, built-in	380 × 380 × 21 mm	3.9 kg
Manta HT, surface-mounted	380 × 380 × 70 mm	4.9 kg

Bottom view. Dimensions and mounting pattern are on the datasheet.

Evidence

Tested, not promised

Every claim carries its condition in the same sentence. You can read more about the test methods at Product Quality and Warranty.

Cleaning · IP69K

High-pressure jet

IP69K means completely dust- and waterproof, including cleaning with a high-pressure jet at close range. Under a canopy, that is not excessive: water and foam are used at a car wash or gas station, and the canopy hangs right in the middle of it. IK08 is the impact resistance of the front, made of diffuse chemically hardened glass or diffuse borosilicate.

Lifespan · TM-21

> 103,500 hours at +50 °C

L90B05 for standard models: at that point, at least 95 % of the fixtures will still deliver at least 90 % of their initial light output. For the HT model, the rated lifespan ranges from 360,000 hours at +50 °C to 51,400 hours at +120 °C.

Practice

CREE 304 positions

The Manta Surface Extended fits perfectly into an existing CREE 304 mounting position: no new cutout, no new wiring, and minimal downtime per location.

Downloads

Data Sheet

The full specification per version, with dimensions and order code. Direct download, no form.

3D file

STEP or DXF for your own drawing, including the assembly pattern and the cutout.

Photometric files

All 8 versions and optics of the Manta in EULUMDAT (.ldt) format, combined into a single 0.8 MB ZIP file. DIALux and Relux can read these files directly. The part number is included in the file name and within the file itself. We provide IES files upon request.

Manual

Installation, wiring, mounting, maintenance and fault finding for the Manta Series in one document of 38 pages, Rev. 1. Download directly in the language of this page.

Also in: Nederlands · English · Deutsch · Français · Español

FAQ

Frequently Asked Questions about the Manta

Can't find your question? Call us with the number of positions and the awning height at hand, and you will know what is needed within five minutes. An engineer will respond within 1 business day.

+31 33 785 9809

Can the Manta replace a CREE 304?

Yes. That’s what the Manta Surface Extended is designed for: the same 380 by 380 millimeters, 118 mm deep, and 5.4 kg, and it fits into an existing CREE 304 cutout. No new cutout, no new wiring. That’s where you save the most money on a retrofit, because if the awning ceiling can remain closed, there’s no need for cutting or breaking work—and no need for a second visit. The part number for this retrofit version is MNAC03; please send a photo of the current situation, and we’ll confirm the fit in advance.

Why are there two lumen values?

22,400 lumens is the luminous flux of the light engine, and 20,600 lumens is what comes out with optics. That difference is normal, because every lens absorbs light. The efficiency therefore ranges from 224 lm/W without specific optics to approximately 206 lm/W with optics. We calculate using the value that corresponds to your chosen optic.

Which version do I need?

That depends on the ceiling. If there is recessed space and you want a seamless finish, then the Recess. If there is no recessed space or it concerns a steel structure, then the Surface. If the luminaire needs to extend further below the ceiling, then the Surface Extended. If you are replacing a CREE 304, then the Surface Extended. And if the environment is warmer than +50 °C, then the HT.

What is the difference between Surface and Surface Extended?

The mounting depth and the weight. The Surface is 70 mm deep and weighs 4.9 kg, the Surface Extended 118 mm and 5.4 kg. Furthermore, they are identical: the same 380 by 380 mm, the same 22,400 lumens, and the same electronics. The Extended is intended for situations where the luminaire needs to extend further below the ceiling.

When do I need the Manta HT?

As soon as the ambient temperature structurally exceeds +50 °C: drying tunnels, drying lines, car washes with steam cleaning, and hot process rooms in the food and paper industries. The HT works up to +120 °C, with chemically tempered glass, a heat-resistant 5-meter SiHF-OB silicone cable, and an external driver outside the hot zone.

How long does the HT version last at high temperature?

That depends on the temperature, and we prefer to write that down rather than give a single number. Measured according to TM-21 and reported as L90B05: 360,000 hours at +50 °C, 103,000 hours at +85 °C, 71,700 hours at +105 °C, and 51,400 hours at +120 °C. Even that last value is still well over fourteen years at ten burning hours per day.

Can the HT be used with a narrower beam?

No. Due to the high temperatures, lenses are not possible; the HT has a single beam angle of 120 degrees, very wide, with a field angle of 168 degrees. If you need a directional beam in a hot zone, a floodlight from our high-temperature line is the right choice and not this canopy.

How is the luminaire dimmed?

With 0-10V, PWM, DALI-2, or via NFC. With NFC, this is done using a smartphone or a programming device, without opening the luminaire and without disconnecting the power. Convenient on a canopy, where every action on a hanging luminaire requires a cherry picker. A position above the pumps can thus be set higher than a position above the drive-through lane.

Do I need an external driver?

Not on the standard versions: the driver is internal and the fixture operates directly from 90 to 305 volts. On the HT version it is, and that is intentional: drivers are more sensitive to heat than the LED module itself, so in a hot zone the driver is the component that fails first. Placed outside the zone, the thermal load decreases and maintenance is possible without entering the hot area.

How many luminaires do I need?

That follows from the dimensions of the awning, the height of the bottom, and the desired light level. As a rule of thumb for a canopy, the spacing should be approximately equal to the height; too far apart will result in dark areas between the positions. We will calculate it and provide the positions and the wattage per position.

What standards apply to a petrol station?

EN 12464-2 sets the requirements for the lighting of outdoor workplaces, and a petrol station canopy falls under that: illuminance, uniformity and glare. We assess the calculation against this. If the station borders on residential areas or nature, the NSVV guideline on light nuisance also applies.

Is the Manta ATEX or Ex certified?

No. For many petrol station canopies, the general lighting falls outside the ATEX zone, but this must always be checked per location and zoning plan. If your situation requires a certified luminaire within the zone, we will state this in advance and refer you to another supplier.

What standards and certifications does the Manta have?

CE and IEC/EN 60598-1 and -2-5 for luminaire safety. EMC emission and immunity have been tested by TÜV according to EN 55015 and EN 61547, and for maritime applications IEC 60533 for engine room, bridge and open deck. Furthermore, IEC 60529 and ISO 20653 for ingress protection classes, IEC 62262 for IK08, ISO 9223 class C5 for corrosion, and RoHS and REACH by self-declaration.

What do IP69K and IK08 mean here?

IP69K means completely dust- and waterproof, including cleaning with a high-pressure water jet at close range. Under a canopy, that is not excessive: water and foam are used at a car wash or gas station, and the canopy hangs right in the middle of it. IK08 is the impact resistance of the front; the front is diffuse chemically tempered glass or diffuse borosilicate glass.

How much maintenance does the fixture require?

Maintenance is the real cost factor for a canopy: each service requires an aerial lift and usually a cordoned-off area. The fixture itself has no wear parts; the recommended inspection is limited to cleaning the front and checking the mounting and the cable entry. On the HT model, the driver is located externally and can be replaced without disassembling the fixture.

What is the difference between this and the DarkLicht WP wallpack?

The WP is a wall-mounted fixture with a full cut-off reflector that directs the light forward. The Manta hangs beneath an awning or ceiling and illuminates the floor below it. Different positions, different light patterns; they are not interchangeable.

What warranty applies?

A five-year limited product warranty on all models, including the HT. For larger projects and chains with multiple locations, extended warranty agreements are negotiable; we tailor these on a case-by-case basis.

Request

Get your awning calculated

Provide the dimensions of the canopy, the height and the number of positions, plus what is currently installed. We will determine the number of fixtures, the power per position, the optics and the design, and put the energy consumption next to your current installation.

Lucas de Graaf

Technical Director, JEL Products

033-7859809

You will receive a response from the person who is also preparing your lighting calculation.

A reply within one working day, from an engineer
Free lighting calculation, with comparison to your current installation
Recess, Surface, Surface Extended, HT and the Upgrade panel
5 years on the complete luminaire for all versions, including the HT

Rather direct contact

+31 (0)33 785 9809

We respond within one working day. We deliver standard items within a week. Custom work, such as a different light colour, a different CRI or a bespoke version, by arrangement.

We use your information solely to review your request and respond to it.