...

Blog

What is the influence of colour rendering on safety in hot production environments?

Colour rendering has a direct influence on safety in hot production environments. Poor colour rendering makes it harder to recognise hazardous situations, signal colours and material deviations in time, which increases the risk of accidents. In this article we answer the most frequently asked questions about CRI, extreme heat and suitable lighting solutions for industrial workplaces.

Which CRI value is safe enough for industrial work?

For industrial work, a CRI of at least Ra 80 is the lower limit for safe working. For tasks where colour recognition is crucial, such as assessing the condition of materials, reading colour-coded pipes or working with hazardous substances, a CRI of Ra 90 or higher is recommended. The closer to Ra 100, the more accurately colours are rendered.

The Ra value, also called the colour rendering index, indicates how well a light source renders colours compared with natural daylight. A light source with Ra 100 renders colours perfectly. In practice, an Ra of 80 means that colours are reasonably recognisable, but subtle colour differences can be lost.

In production environments with heat, dust or 24/7 operations, choosing a high CRI value is not just a matter of comfort. Employees working with colour-coded systems, wear indicators or product quality control need an accurate colour picture to do their work safely and correctly.

How does poor colour rendering affect employee safety?

When lighting distorts or washes out colours, employees can miss hazardous situations they would notice immediately under better lighting. Think of a red warning indicator that looks orange, a damaged pipe that goes unnoticed, or a product with a deviating colour that indicates a production fault.

The consequences of poor colour rendering on the shop floor are concrete:

  • Colour-coded pipes, safety signs and emergency exits are recognised less quickly
  • Material deviations and surface damage are harder to see during inspection
  • Personal protective equipment with specific signal colours stands out less
  • Fatigue increases because the eye works harder to interpret colours
  • Quality control becomes less reliable, which can let defective products slip through

The danger often lies in habituation. Employees adapt to poor lighting without realising how much information they are actually missing. Only when the lighting is improved does it become clear how limited their view was before.

What does extreme heat do to the colour rendering of lighting?

High ambient temperatures affect the performance of lighting components, which has a direct effect on colour rendering. LED lighting is sensitive to heat: as the temperature inside the luminaire rises, the light colour shifts and the colour rendering index drops. This process is called thermal degradation and is one of the main causes of reduced lighting quality in hot factory environments.

In environments such as steelworks, foundries or process halls where the ambient temperature is structurally above 40 or 50 degrees Celsius, standard LED luminaires operate outside their thermal design range. The result is not only a shorter lifetime, but also a deteriorating light colour and a lower Ra value during use. The lighting may still seem to work, but no longer performs as intended.

With exposure to infrared radiation, such as near melting furnaces or heat treatment installations, the problem is even greater. Infrared radiation heats the luminaire from the outside, regardless of the ambient air. Conventional luminaires are not designed for this and quickly lose their colour accuracy. For this type of environment, high-temperature lighting is designed specifically to keep working reliably.

Which lighting solutions maintain colour rendering at high temperatures?

Luminaires designed for high ambient temperatures combine thermal management with high-quality LED components to keep colour rendering stable. The key lies in the combination of a robust heat sink, high-temperature-resistant electronics and selected LED chips that deliver a consistent Ra value even at elevated temperatures.

When choosing lighting for hot production environments, these are the relevant features to look out for:

  1. Thermal design: a properly sized heat sink prevents the LED junction temperature from rising too high
  2. Temperature range check whether the luminaire has been tested and certified for the actual ambient temperature
  3. CRI specification at operating temperature: some manufacturers measure CRI under ideal conditions, not at the actual operating temperature
  4. Protection rating: in hot environments, heat often goes hand in hand with dust or fumes, which calls for a high IP rating
  5. Housing material: high-grade aluminium or stainless steel dissipates heat better and extends the lifetime

Luminaires developed specifically for heavy industry, such as those used in steelworks and foundries, are tested for temperature resistance up to 120 degrees Celsius. That is a fundamentally different level than a standard industrial LED luminaire.

When is colour rendering a safety standard rather than a preference?

Colour rendering becomes a safety requirement as soon as the work depends on reliable colour recognition. That applies not only to visual quality control, but also to environments with colour-coded safety systems, hazardous substances or critical signalling. In those cases, a low Ra value is not an aesthetic shortcoming but an operational risk.

Sectors where colour rendering must structurally be considered a safety factor include the chemical industry, the steel industry, the paper industry and environments with explosion hazards. In these environments, employees work with systems where misinterpreting a colour can have direct consequences for the safety of people and installations.

For Heavy industry with extreme heat moreover, lighting quality must be guaranteed not only at commissioning, but also after years of use. Lighting that deteriorates through thermal degradation may still meet the specifications on paper, but no longer in practice.

Practical example: Farm Frites

In the drying tunnels and production ovens of Farm Frites, the previously installed LED lighting failed repeatedly, due to thermal stress and the intensive cleaning that is standard in the food industry. JEL then designed the Snapper HT-SS, a food-grade version of the stainless steel Snapper HT with borosilicate glass, IP69K protection and a HACCP-compliant design. 78 luminaires were supplied, each 35 W. The lighting design was checked against EN 12464-1 and delivers 200 to 500 lux in the oven, with a uniformity of 0.65 to 0.85.

In these kinds of environments, colour rendering cannot be separated from thermal reliability. An LED that degrades through heat not only loses light output but can also shift in light colour, so that colour differences in the product or installation are perceived differently. A luminaire that stays thermally stable also keeps its colour rendering closer to the specification.

Light that lasts is also predictable light. An installation that illuminates evenly and does not keep partially failing gives employees a constant picture of colours and contrasts, and that counts for safety markings and process indications.

Read more about the Farm Frites project

How JEL Products helps with colour rendering in hot production environments

JEL Products supplies LED luminaires designed specifically for the conditions where standard lighting falls short. For colour rendering in hot production environments, that means in concrete terms:

  • Luminaires with a guaranteed CRI value at actual operating temperatures, not just under laboratory conditions
  • High-temperature floodlights such as the Orca and Barracuda, tested up to 120 degrees Celsius and resistant to infrared radiation
  • Customised lighting design, in which the Ra value is matched to the specific tasks and safety requirements of the environment
  • Guidance throughout the entire process: from engineering and design to installation and commissioning
  • ISO 9001 and VCA** certified working methods for quality assurance in every project

Whether it concerns a steelworks, a chemical plant or a production facility with extreme conditions: choosing the right colour rendering starts with good lighting advice. Get in touch via the JEL Products Contact Page to discuss which solution suits your situation.

Related Articles